New arrival Tire Pressure M-onitoring Sensor TPMS-19 8C2Z-1 A203-A Compatible for Ford Vehicles

Product Description

Tire Pressure M-onitoring Sensor TPMS Compatible for F-o-r-d;

 Interchange Part Number: TPMS-19, 8C2Z-1A203-A;

 Replaces your old and damaged one;

 Placement on Vehicle: Front-Rear, Left, Right,clockwise.

 

 

 

Vehicle In Coverage	2008-2016 for Ford E-150 E-250 E-350 E-450 Econoline	2008-2016 for MKZ
2008-2016 for Ford F-250 F-350 F-450 F-550 Super Duty	2008-2016 for Ford Fiesta	2008-2016 for MKS
2007-2016 for Ford Mustang	2008-2016 for Ford	2008-2016 for Navigator
2007-2014 for Ford Edge	2008-2016 for Ford	2008-2011 for Town Car
2006-2016 for Ford Escape	2008-2011 for Ford Crown Victoria	2007-2008 for Mark LT
2008-2016 for Ford Expedition	2011-2016 for Ford Transit Connect	2006-2010 for Mountaineer
2006-2016 for Ford Explorer	2006-2011 for Ford Ranger	2006-2010 for Monterey
2008-2015 for Ford	2007-2016 for MKX	2006-2011 for Mariner
2008-2016 for Ford Taurus	2007-2016 for MKT	2007-2016 for Ford F-150

 

 How to Train for Ford Tire Pressure M-onitoring SensorsTPMS?

1. Turn the ignition switch to the OFF position, then press and release the brake pedal.

2. Cycle the ignition switch from the OFF position to the RUN position for 3 times, ending in the RUN position.

3. Press and release the brake pedal.

4. Turn the ignition switch to the OFF position.

5. Turn the ignition switch from the OFF position to the RUN position 3 times, ending in the RUN position.  

(The horn will sound once and the TPMS indicator will flash if the training mode has been entered successfully. If equipped, the message center will display TRAIN LF TIRE.)

 

6. Place the tire pressure m-onitoring activation tool on the LEFT (Driver’s Side) FRONT tire sidewall at the valve stem.

    Press and release the test button repeatedly on the TPMS Tool until the horn beeps.  

   (It may take up to 6 seconds for the tool to activate the sensor, Leave the tool on the sidewall for the entire 6 seconds).  

   The horn beeping indicates that the body control module has recognized the TPMS sensor.

7.Within 2 minutes of the horn sounding confirming programming of the LF tire, place the TPMS tool on the RIGHT (Passenger’s Side) FRONT tire

    sidewall at the valve stem and press the test button to activate the sensor.

8. Repeat step 7 for RIGHT REAR followed by LEFT REAR tire in that order.  The procedure is complete after the last tire has been trained.  

    When training is complete, the message center (if equipped) will display TIRE TRAINING COMPLETE.

    For vehicles not equipped with a message center, successful completion of the training procedure is verified by turning the key to the

   OFF position without the horn sounding.  If the horn beeps twice when the switch is turned to OFF the training procedure was not successful.

 

NOTE 1): If the vehicle or wheels/sensors have been stationary for more than 30 minutes, the sensors will go into a “sleep mode” to conserve battery power.

                 It is necessary to wake them up by simply moving them or rolling the tires before they will communicate with the vehicle.

NOTE 2):The TPMS training procedure must be done on one vehicle at a time, in an area without radio frequency interference – at least 3 feet away from other vehicles equipped with TPMS sensors.

NOTE 3):Vehicles with different tire pressures front-rear like F-Series trucks and E-Series vans also require TPMS re-training after a tire rotation. Failure to train the sensors will cause the TPMS warning light to illuminate on the dash.

HOME